FlexCoat System

FlexCoat is a “crackbridging” Elastomeric coating designed for exterior walls waterproof. It is formulated with the highest quality resins and raw materials available to form a tough yet flexible mildew-resistant coating for masonry substrates. The coating is highly elastic and resistant to pollutants.  It is designed for

  • Stucco wall waterproofing and crack bridging
  • Concrete wall waterproofing and crack bridging
  • Brick and masonry wall waterproofing and crack bridging
  • Concrete block wall waterproofing and cracking
  • Metal exterior wall waterproofing, decorating and crack bridging
Advantages & Benefits:
  • So flexible that it can move with cracks
  • Excellent adhesion
  • Ultra Violet resistant for extra durability
  • “ Light-solidifying nuclear shell ” effect, strongly resistant to pollutants
  • Mildew-resistant
  • “Skin breathing” effect stops moistures from gathering within the walls
  • Extraordinary weathering-resistant and long colour-retention
  • Smooth coating and exquisite colours
  • Fungus resistance to keep the surface clean
  • Meets V.O.C. emission regulations to eliminate facility downtime during application.
  • Non-toxic formulation is safe to install
  • A wide range of fabulous architectural colours available
  • Easy application and cleanup
  • Last up to 15 years under a proper maintenance schedule

Technical Data:

Series

Inspection projectStandard

Index values

1

State in the containerGB/T9755-2001

Lump-free when it is stirred evenly

2

Application abilityGB/T9755-2001

Can be applied up to 2 coats

3

Stability in low temperaturesGB/T9755-2001

Maintain excellent conditions

4

Drying timeGB/T9755-2001

≤2h (surface)
24h (full cure)
≤7d (complete solidification)

5

Coating colours and appearanceGB/T9755-2001

Coating appearance remains unchanged,Colour variance△E≤0.2

6

Contrast ratio (white) GB/T9755-2001

0.95

7

Water-tolerance (96h) GB/T9755-2001

No effects noted

8

Alkali resistance (48h) GB/T9755-2001

No effects noted

9

Outstanding ability to bear scrubbing, timesGB/T9755-2001

≥5000

10

Dirt-resistancedecline rate of reflection coefficient (White 5 times), %GB/T9755-2001

≤10

11

Ability to bear temperature changes10 times)(GB/T9755-2001

No effects noted

12

Elongation (ASTM D638)

3.24MPa(1mm)

13

Tensile strength of cured system

 (ASTM D412)

300-600%

14

Aging resistance (ASTM G26)

1000h No effects noted

15

Algae and fungus resistanceASTM G29

No growth supported

16

Air permeabilityASTM G96

3perms

17

Ultra violet resistance

Excellent

18

Lower temperature flexibility

Bend at -25 no crackles

19

Shelf life and storage conditions 

18 months if unopened /Do not freeze it

Application Specifics:

     Surface Preparation:

    Remove any loose or flaking particles, lubricants, dirt, or mildew. All existing surfaces should be power washed. Fill the gaps and any cracks with BarerNeat. Smoothen the surface and keep it clean and dry.

       Application:

(A)    If any surfaces exhibit chalking after they have been properly power washed, they must be primed with one coat of SubonPrimer. Dry time/Approximately 8 hours.

(B)  Apply FlexCoat evenly to the primed surface. Allow 8 hours between coats to dry completely. (At lower temperatures, more drying time may be needed.)

(C)  Apply the second coat of FlexCoat by brushes, sprayers or rollers. Allow at least 8 hours between coats to dry completely. 

(D)    The third coat of FlexCoat is recommended. Application temperature should be higher than 4. Relative humidity is below 85%.

Clean Up :

      Protect adjacent surfaces not receiving waterproofing. FlexCoat is easily cleaned with water when still wet. Dried material can be removed with a water-soluble solvent.


USA Hydro-Stop (CHINA) CO.,LTD
Add:21/FL , NEW World Towerl.18 queen's Road Center , HK
Tel:852-2971-2851   Fax:852-3519-9727

Approvals
A world leader in producing environmentally safe roofing and waterproofing systems.